JIS K 2. RRP: Your Price: $1, SKU: JIS K 2. Vendor: Condition : Weight: LBS. Availability: Shipping: Calculated at checkout. Minimum. Find the most up-to-date version of JSA – JIS K at Engineering MS ISO BS ISO ASTM D JIS K (Clause 6). DIN AS MS ISO 3) Air Permeability.
|Published (Last):||17 November 2016|
|PDF File Size:||6.40 Mb|
|ePub File Size:||14.53 Mb|
|Price:||Free* [*Free Regsitration Required]|
Pressure foot The Pressure foot in contact with the specimen is 44mm in width and 18mm in depth, wide enough to ensure accurate measurement.
Our product line consists of various types of durometers applicable to specific materials as indicated in the chart above. Hardness Tester Selection Chart 63301 product line consists of jis k 6301 types of durometers applicable to specific materials as indicated in jis k 6301 chart above.
High accuracy and repeatability of the hardness readings are assured by the flexible joint function. Night line and highest and lowest limiter equipped for the both are standard.
Standard: JSA – JIS K 6301
However, it is used even now for measurement data or internal management data upon the agreement of concerned parties due to its extensive use for many years within the rubber industry. This is basically equal to JIS K of durometeras only its round up method of spring load jis k 6301 etc. Indentor Extension Tester The 631 to check the indentor height on a durometer and the reading indicator mechanism. Load Tester for Hardness Tester Tester to check load properties of the spring on a durometer Inspection is conducted at 25, 50, and 75 points jia.
Measurement example Hardness is being measured by jis k 6301 GS G on the sponge sheet.
JSA – JIS K – Physical Testing Methods for Vulcanized Rubber; Errata – 5/ | Engineering
It consists of 3 types of durometer such as Type A jjs medium stiffness, Type D for high hardness and Type D for low hardness. Two-pointer type max-hand and active hand of Rubber Hardness Tester The stationary set jis k 6301 max-hand makes the maximum value easier to read and allows the creep characteristics of a specimen. This standard is ruled by plastic business field in Japan apart from testing method of hardness of jis k 6301. The stationary set hand max-hand makes the maximum value easier to read and allows the creep characteristics of a specimen.
Please select according to usage in addition to type A and Type D. At that time, deep hole H and long leg type Jis k 6301 make measurement possible by making pressed face small or long. In case there unevenness on the measured face, less flat face because of irregular shape and mis bump at the bottom, depressed face of durometer is jis k 6301 to reach and sometimes accurate jis k 6301 is not possible.
Type D is suitable for hard rubber of which measured figure by Type A 90 and above and Type E is suitable for soft rubber of which measured figure is below GS 4kg weight option ZY The most important consideration in using durometers is to select the correct type for purposes of measurement according to the specimen.
Type A which is main type tends to indicate higher jis k 6301 by 1 or 2 points compared with conventional A hardness measurement. However, it was used for 50 years as rubber hardness measurement and is still used as test data agreed between jis k 6301 persons even now when it is progressed to shift ijs new JIS and the standard is discontinued.
Jix are 2 kinds of A type for general rubber jis k 6301 C type for hard rubber. As is half ball type osibari this is suitable for soft material like soft rubber expanded rubberhardness jis k 6301 spool of textile and film roll to which osibari sticks if it is type A durometer. But we distinguish model code as another durometer from conformity of standard point of view.
Then, long leg type complies with DIN Type E 2 durometer with around half of sponge spring load figure 63001 type E, and type FO jis k 6301 measure hardness of polystyrene sponge for the level of sponge washing dishes are available. To top of product information.
ASKER Durometer Type JC | Product | KOBUNSHI KEIKI CO.,LTD.
Dispersion of polystyrene level can be judged. JIS K which had been established in and sustaining the base of rubber industry in Japan was discontinued in after the suspended period, as it jis k 6301 not in conformity with ISO, and JIS K was newly established.
Inspection is conducted at 2, 50, and points respectively. The Pressure foot in contact with the specimen is 44mm in width and 18mm in depth, wide enough to jis k 6301 accurate jjis.
Constant Jis k 6301 for Durometer Constant loarder assures uniform test pressure eliminating false readings due to differences between operators in measuring by hand. However, verification is recommended because a significant difference is estimated to be the largest when a durometer indicates measurement values from 10 to 90 points.